How to choose a spin coater: a buyer’s checklist for the UK and Europe
A spin coater is a simple machine on paper, and the differences between models only show once it’s in daily use. The questions below are the ones we work through with every lab and fab before we quote. Answering them first saves time, and it makes quotes from different suppliers easy to compare.
1. Substrates
- Sizes and shapes. List every substrate you’ll coat, from the smallest piece to the largest wafer or plate. Round, square and odd-shaped parts need different chucks.
- Thickness and weight. Thin or brittle wafers need porous chucks. Heavy glass plates need a motor that can accelerate the load as programmed.
- Future work. A tool that takes 150 mm today may need 200 mm or large plates later. Bowl size and chuck range are hard to change after purchase.
Our chuck guide covers holding each type of substrate.
2. Speed and control
- Top speed and acceleration. Thin films need high speeds and fast ramps. Large substrates need high torque more than high speed. Ask for acceleration figures with a real load, as well as unloaded.
- Repeatability. Speed resolution and repeatability decide how closely runs match. Look for a figure in rpm, and ask how it’s held under load.
- Recipes. Check how many steps a recipe can have, how finely each is timed, and whether speed, acceleration, dispense and exhaust can all change by step.
3. Chemistry
List the resists, solvents and other materials you’ll spin. They decide the bowl material, the chuck material and whether the tool needs solvent-resistant seals throughout. Ask how the drive and bearings are protected from liquid, and whether fumes and waste leave the bowl by separate paths.
4. Dispense
Hand dispense by pipette or syringe suits research and trials. Automated dispense gives the same volume and timing every run, and becomes worthwhile as soon as repeatability matters or more than one person runs the tool. Check how many dispense lines the lid takes, and whether automation can be added later. Our dispensing guide compares the options.
5. Edge bead and backside rinse
Thick films, square parts and contact exposure all make edge bead removal more likely to be needed. Backside rinse protects downstream tools. Both are easier to fit at purchase than later. See our edge bead guide.
6. Atmosphere and exhaust
A closed bowl with programmable exhaust gives the most control over drying, and it’s the main defence against striations and the cotton candy effect. For air-sensitive materials, ask about a nitrogen purge or glove box use. Our nitrogen and glove box guide covers both.
7. Mounting and layout
Spin coaters come as benchtop units, flange-mounted modules set into a wet deck, or modules inside a workstation alongside bake plates and developers. Think about where the tool will sit, how it’s exhausted, and whether you’ll add more process steps beside it.
8. Utilities
Every coater needs power and vacuum, and usually nitrogen and exhaust. Confirm the mains voltage, the vacuum level and flow, the nitrogen pressure and the exhaust flow the tool needs, and whether a vacuum pump is included or available.
9. Data and safety
- Process data. Logging speed, vacuum, exhaust, temperature and humidity for every run makes troubleshooting far quicker and supports quality records.
- Safety. Lid and vacuum interlocks should stop a run if the lid is open or the substrate isn’t held.
- CE marking. In the UK and the EU, a process tool should arrive CE marked with an EU declaration of conformity. North American NRTL marks such as ETL or UL don’t replace it. Our guide to CE, UKCA and NRTL explains what to ask for.
10. Support
Ask who installs the tool, who trains your team, who handles warranty claims and how quickly an engineer can reach you. A local distributor with its own service team, spares and process support makes a real difference over the life of the tool. Ask too how long the maker supports older tools.
Putting it together
Once you’ve answered these questions, a supplier can quote the right configuration first time. Configuration, especially mounting and dispense, drives most of the price difference between quotes, so compare like for like.
How SiSTEM can help
We supply Apogee spin coaters from Cost Effective Equipment across the UK and Europe, with installation, training and warranty support from our own after-sales team. Send us your substrates, materials and layout, and we’ll come back with a configuration and quote. Apogee spin coaters are very popular with universities and research institutes across the UK and Europe, and with spin-out companies.