Glossary of spin coating and lithography terms

Short definitions of the terms used across our technical guides, with links to the guide that covers each one in more detail.

A to D

  • Acceleration (ramp). How quickly the spin coater reaches its set speed, in rpm per second. Fast ramps suit thin films, slow ramps suit thick, viscous materials. See spin coating theory.
  • Adhesion promoter. A surface treatment, usually HMDS, that helps resist bond to the substrate. See HMDS and adhesion promotion.
  • Antisolvent. A liquid dripped onto a spinning film to trigger fast crystallisation, mainly in perovskite processing. See nitrogen and glove boxes.
  • Backside rinse (BSR). A solvent or DI water spray onto the underside of the spinning substrate to clean off material that wrapped round. See edge bead removal.
  • Bilayer. A lift-off stack of an underlayer that develops quickly beneath a standard resist, giving an undercut. See metal lift-off.
  • Captive chuck. A chuck with guides that locate the substrate mechanically. See choosing a spin chuck.
  • Carrier wafer. The rigid wafer a thin device wafer is bonded to during processing. See adhesives and carriers.
  • Chemically amplified resist (CAR). A resist in which exposure creates a catalyst, and the post-exposure bake drives the reaction.
  • Chuck mark. A faint circle in the film caused by the chuck changing the substrate temperature locally. See spin coating defects.
  • Comet. A streak in the film behind a particle or bubble.
  • Cotton candy effect. Fine fibres of dried material that form at the substrate edge during spinning. See the cotton candy effect.
  • Debond. Separating a thinned wafer from its carrier. See debonding methods.
  • Dehydration bake. A bake that drives water off the substrate before priming or coating. See the bakes in lithography.
  • Dewetting. A film pulling back into islands because it doesn’t wet the surface.
  • DNQ resist. The most common type of positive photoresist, based on diazonaphthoquinone.
  • Dynamic dispense. Dispensing onto a slowly spinning substrate. See dispensing.

E to O

  • Edge bead. The thicker rim of film at the substrate edge. See edge bead removal.
  • Edge bead removal (EBR). Clearing the edge bead with solvent, exposure or by hand.
  • Exhaust. Airflow drawn from the spin bowl. It removes vapour and affects drying rate.
  • Film frame. A ring with dicing tape stretched across it, used to hold thin wafers.
  • Flange mount. A spin coater, developer or bake plate set into a wet deck, with the bowl and drive below the surface.
  • Hard bake. A bake after development that hardens the resist for etching or plating.
  • HMDS. Hexamethyldisilazane, the standard adhesion promoter for resist on oxides.
  • Image reversal. A process that turns a positive resist into a negative-acting one, often for lift-off.
  • LEV. Local exhaust ventilation, which in the UK must be tested at least every 14 months. See planning a lithography workstation.
  • Lift-off. Patterning metal by depositing it over a resist pattern and dissolving the resist. See metal lift-off.
  • Lift pins. Pins that hold a substrate above a hotplate for proximity baking and staged heating. See bake methods and ramping.

P to Z

  • Porous chuck. A chuck with porous ceramic that spreads vacuum across the whole back of a thin or flexible substrate.
  • Post-exposure bake (PEB). A bake after exposure that drives the chemistry in chemically amplified and negative resists.
  • Proximity baking. Baking with the substrate held just above the plate on gas or pins.
  • Puddle development. Developing with a standing puddle of developer on the substrate. See developing photoresist.
  • Recessed chuck. A chuck that holds a square part in a pocket, flush with the surface. See coating squares.
  • Rehydration. The time a DNQ resist needs after the softbake to take water back from the air before developing.
  • Softbake. The bake after coating that removes most of the solvent.
  • Spin curve. A chart of film thickness against spin speed for a material.
  • Spray development. Developing with a continuous spray of developer onto the spinning substrate.
  • Static dispense. Dispensing onto a stationary substrate before the spin.
  • Striations. Fine radial lines in a film caused by uneven evaporation.
  • Suckback. A valve action that draws liquid back into the dispense tip to stop drips.
  • Temporary bonding. Fixing a device wafer to a carrier for thinning and backside processing. See why wafers are temporarily bonded.
  • Thermal slide debond. Heating a bonded pair until the adhesive softens, then sliding the wafers apart.
  • TTV. Total thickness variation, the difference between the thickest and thinnest points of a wafer or bonded stack.
  • Undercut. A resist profile that’s wider at the base than the top.
  • Void. A pocket of trapped air or solvent in a bond.

More technical guides

All technical guides